Honeywell S9200U1000 Universal Furnace Control Board

Fits the Following:

United Technologies 1012-925A, 1012-925B, 1012-925C, 1012-955A, 1012955A, 1012-83-9651B, 1012-930, 1012933D, 1012-933D, 1012-83-9336AHSC1, 1012-83-9337A

Rheem/Robertshaw 62-24268-01, 62-24268-02, 62-24268-03, 695-200

Nordyne 624557, 6245570, 624557-0, 624564, 6245640, 624591, 624591A, 624591-A, 624591-B, 624591-C, 624591-D, 624628, 624628-0, 6246310, 624631-0, 624631A, 624631-A, 624631-B, 710128A, 902378, 902696, 903106, CAR903106

Texas Instruments 6DT-1, 6DT-2, 61F3, 41F-5

York 03100662000, 031-00662-000, 031-00662-700, 031-01140-000, 031-01140-001, 031011140002, 031-01140-002, 031-01140-701, 031-01140-702, 031.01234.000, 031-01234-700, 0310123500, 031-01235-700, 031-01250-000, 03101266000, 0310126700, 031-01267-000, 031-01267-001, 031-01267-001A, 031-01284-000, 03101933000, 031-01933-000, 031-01972-000, 031-01973-000, 031-02166-000, 03109166000, 03109167000, 33101933000, 331-01933-000, 33109167000, 331-01972-200, 43101972100, 431-01972-100, P03101267001, P031-01267-001, P031-01267-001, PTH031011400-00, CAR33101972200, CAR03101973000, CAR50A55843,G951ADB1401, G951ADB1401C, G951ADB-1401C, G951ADB1402,

G951ADB-1402, G951AEB-1403

White-Rodgers 50T50-730, 50T35-743, 50A55-120, 50A55-286, 50A55-438, 50A55-474, 50A55-571, 50A55-843, 50A50-143, 50A50-286, 50A50-438, 50A50-209, 50A50-230, 50A55-241

Goodman 1809913, 18099-13S, B180996, B1809906, B18099-6, B18099-06, B1809908, B18099-08, B1809910, B18099-10, B18009910, B180099-10, B1809913, B18099-13, B1809913S, B18099-13S, B18009913, B180099-13, CARB1809913S

ICM ICM280

Features

• Cross reference and wire harnesses provided for simple replacement over 195 existing furnace controls.

• Main burner ignition using a 120V hot surface igniter.

• Flame rectification circuit to monitor flame presence.

• Monitoring of system pressure switch, high temperature limit, and rollout functions.

• Appliance operation/safety requirements controlled via microprocessor.

• Controls circulating fan motor based on appliance requirements, in response to a conventional low voltage thermostat.

• LED system status, performance and diagnostic indication.

• Twinning capability

Product Specifications

Application: Single stage warm air furnaces

Frequency: 60 Hz

Operating Humidity Range (% RH): 0% to 95% non-condensing

Operating Temperature Range (F):   -40 F to +175 F

Operating Temperature Range (C):  -40 C to +79 C

Flame Failure Response Time (sec):  2 Seconds max @ 1µA

PrePurge:  30 seconds

PostPurge:  15 seconds

Cool Fan On Delay:  5 seconds

Cool Fan Off Delay:  0 or 60 seconds

Line Voltage:  120 Vac (97-132 Vac)

Low Voltage:  24V (18-30 Vac)

Igniter Current: 5 A resistive @ 120VAC

Thermostat Anticipator Setting: (Stage 1 only) 100mA

HSI Warmup Time: 17/27 or 30/30 seconds

Trial For Ignition:  4, 6, or 8 seconds

Interpurge: 60 seconds

Ignition Trials: Three, two tries if flame is not sensed

Number of LEDs: 3

Heat On Fan Delay: 30 or 60 seconds

Heat Off Fan Delay: 60, 90, 120, or 180 Seconds

Gas Control Used With:  Any 24Vac redundant, direct ignition gas control rated at 1.5A or less. Honeywell VR8205 recommended.

Cooling Contactor Used With:   Any 24Vac contactor rated at 1.0A or less

Induced Draft Blower Load: 2.2FLA / 25LRA max @120Vac

Ciculator Load: 14.5FLA / 25LRA max @120Vac

Type of Fan Used With: Standard Induction-Type Circulating Fan